SMLA-SERIES

SMLA-SERIES

分  类:测量测试仪器

品  牌:欧米茄

厂  商:Omega工业测量(中国)

型  号:SMLA-SERIES

相关行业:

发布时间:2019-12-19 16:51 浏览人数:

最新产品

产品详情
参数
包装
  • SMLA-1 (Single Trip, DPDT, 5A) SMLA-2 (Single/Dual Trip, 2 SPDT, 5A)
  • Field Configurable Input Ranges for DC Voltage and Current
  • Exclusive “Dynamic Deadband” Prevents False Trips
  • Provides Relay Contact Closures at a Preset DC Input Level
  • Programmable HI or LO Setpoints
  • Failsafe/Latching Operation
  • Selectable 120/240 Vac Input Power

  • SMLA-1 single setpoint and SMLA-2 dual setpoint limitalarms offer flexible, wide-ranging DC input capability.Voltage spans from 10 mV to 200V and current spansfrom 1 mA to 100 mA can be field configured. Bipolarinputs are also accepted. Both models offer configurablelatching, failsafe and HI/LO operation. The SMLA-1and SMLA-2 also include 0.25% to 50% adjustabledeadbands and selectable 120/240 Vac input power.

    Models SMLA-1 and SMLA-2 are equipped with a dualfunction diagnostic LED. The green center LED indicatesline power and input signal status. Active line poweris indicated by an illuminated LED. If the center LEDis off, check line power and the wiring connection. Ifthe input signal is above 100% full scale, the LED willflash at approximately 8 Hz. Below 0%, the flash rate isapproximately 4 Hz.

    The single setpoint SMLA-1 and the dual setpointSMLA-2 provide the following relay outputs: SMLA-1Single Trip (DPDT, 5A); SMLA-2 Single/Dual Trip(2 SPDT, 5A). Setpoints are top accessed multi-turnpotentiometers.

    The field configurable SMLA-1 and SMLA-2 limit alarmsetpoints can be configured for HI, LO, latching or failsafetrip operation. Non-latching HI and LO setpoints haverespective HI and LO deadbands. In a tripped condition,the setpoint is exceeded and the appropriate red LED willilluminate. The trip will reset only when the process fallsbelow the HI deadband or rises above the LO deadband.To reset a latched setpoint the signal must be in the saferegion and the line power turned off for at least 5 seconds.For proper deadband operation, a HI setpoint must alwaysbe set above a LO setpoint.

    In failsafe operation, the relay is energized when theprocess is below the HI setpoint or above the LO setpoint(opposite for nonfailsafe). In the failsafe mode, the relaysgo to the tripped condition when the power fails.

    The input must remain beyond the setpoint for100 milliseconds, uninterrupted, to qualify as a validtrip condition. Likewise, the input must fall outside thedeadband and remain there for 100 milliseconds to returnthe alarm to an untripped condition. This effectively resultsin a “dynamic deadband” - based on time - in addition tothe normal deadband.

    Specifications
    INPUT
    Voltage Input (Unipolar or Bipolar):

        Range: 10 mV, 20 mV, 50 mV, 100 mV, 200 mV, 500 mV, 1V, 2V, 5V, 10V, 20V, 50V, 100V, 200V (dip-switch selectable)
        Impedance: >100 kΩ
        Overvoltage: 400V max
    Current Input (Unipolar or Bipolar):
        Range: 1 mA, 2 mA, 5 mA, 10 mA, 20 mA, 50 mA, 100 mA(dip-switch selectable)
        Impedance: 20 Ω typical
        Overcurrent: 200 mA max
        Overvoltage: 60 Vdc
    Common Mode (Input to Ground): 1000 Vdc max
    LED Indications:
        Input Range (Green):
          >100% Input: 8 Hz flash
          <0% Input: 4 Hz flash
        Setpoint (Red):
          Tripped: Solid red
          Safe: Off
    Limit Differential (Deadband):
        >50 mV/5 mA: 0.25% to 50% of span
        <50 mV/5 mA: 1% to 50% of span
    Response Time:
        Dynamic Deadband: Relay status will change when propersetpoint/process condition exists uninterrupted
        for 100 msec
        Normal Mode (Analog Filtering): <250 msec, (10 to 90%)
    Setpoint:
        Effectivity: Setpoints are adjustable over 100% of theselected input span
        Repeatability (Constant Temp):
          >50 mV/5 mA: 0.1% of full scale
          <50 mV/5 mA: 0.2% of full scale
    Stability:
        Line Voltage: ±0.01%/% max
        Temperature: ±0.05% of full scale/°C max
    Common Mode Rejection: DC to 60 Hz: 120 dB
    Isolation: 1000 Vdc between contacts, input and power
    ESD Susceptibility: Meets IEC 801-2, Level 2 (4 KV)
    Humidity:
        Operating: 15 to 95 %RH @ 45°C (113°F)
        Soak: 90 %RH for 24 hours @ 65°C (149°F)
    Temperature Range:
        Operating: 0 to 60°C (32 to 140°F)
        Storage: -15 to 70°C (5 to 158°F)
    Power: 120/240 Vac ± 10%, 50 to 60 Hz selectable, 2 W typical, 5 W max
    Relay Contacts:
        SMLA-1: DPDT (2 Form C)
        SMLA-2: 1 SPDT (1 Form C) per setpoint
        Current Rating (Resistive): 120 Vac: 5A; 240 Vac: 2A;28 Vdc: 5A (external relay contact protection
        is required for use with inductive loads)
        Material: Silver-Cadmium Oxide
        Electrical Life: 105 operations at rated load
        Mechanical Life: 107 operations
    Latch Reset Time: 5 seconds
    Weight:
        SMLA-1: 209 g (0.46 lb)
        SMLA-2: 282 g (0.62 lb)



































































暂无内容提供
暂无内容提供

联系方式

中国自动化网安全提示,在购买供应商商品时,请一定要先审核好企业信息是否真实,谨防网上诈骗。
公司名称:Omega工业测量(中国)
联系人: 王先生
联系电话:02161973664
手机号:
传 真:
电子信箱:kevin.wang@cn.omega.com
公司网站:http://cn.omega.com
公司地址:上海市宜山路1698号102单元
留言反馈
  • 评价:

  • 关于:

  • 联系人:

  • 联系电话:

  • 联系邮箱:

  • 需求意向:

  • 验证码:

    看不清楚?

  • 在线咨询
X
下载企业APP

成为企业会员免费生成APP!